Wenesco High Temperature Pumps

© 2018 Designed by Adam Victorn - Wenesco - Entire site copyright 1998-2019 by LDS Industries, LLC. All rights reserved.

Microptik BV is our distributor serving Europe, the Middle East, Africa, and Asia. Visit their site: www.wenesco.eu

Wenesco High-Temperature Pumps

 

For any questions regarding our High-Temperature Pumps, please reach out to Enver Poljak, at Enver@wenesco.com.

Wenesco High-temperature Pumps are used for transferring molten salt, zinc, lead, and other non-viscous material at 700C.

These centrifugal pumps, with no seals, require only minimal maintenance. They are available with electric or air motors.

Wenesco Model HTP1  with 1-HP motor
Wenesco Pump. Wenesco Pump Total Head in feet vs capacity in US gallons per minute

TUBE FRAME PUMPS

  • Select 120 or 240V for electric motor

  • Select 304 stainless steel or cast iron construction

  • Starter with thermal protection

  • Discharge: 1.25 NPT

  • Complete air control for air motor

  • 316 SS construction optional at additional cost

  • Gussets for lowering pump during operation

  • VFD Speed control optional at additional cost

Wenesco Model HTP1 with air motor
Wenesco Pump Total Head in feet vs capacity in lb/min
Model HTP2 with 2-HP motor
Wenesco Pump Diagram
Molten Salt Pumps
Wenesco Molten Salt Pump custom made for mounting in our customer’s tank
Wenesco This temperature-controlled heated tank, combined with a high temperature pump  delivers molten salt, used as a coolant. to a Molten Salt Reactor.
The 316-stainless steel reservoir holds 7-1/2 gallons (120 lb. salt) and will operate up to 700C.  Temperature is controlled with an accurate digital thermostat, while pump speed and flow  are controlled with a Variable Frequency Drive.  Power: 13,800 Watts, 240V single or three-phase. Wenesco Molten Salt Pump

(Above) Molten Salt Pump custom made for mounting in our customer’s tank

Wenesco Molten Salt Loop Test System

(Above) This temperature-controlled heated tank, combined with a high temperature pump
delivers molten salt, used as a coolant. to a Molten Salt Reactor.

The 316-stainless steel reservoir holds 7-1/2 gallons (120 lb. salt) and will operate up to 700C.
Temperature is controlled with an accurate digital thermostat, while pump speed and flow
are controlled with a Variable Frequency Drive. 

 

Power: 13,800 Watts, 240V single or three-phase.

(To The Left) Molten Salt Loop Test System

(Below) This pump for molten salt features an immersion depth of 144 inches. It is made from 316 stainless steel. This pump includes a 3-in NPT discharge pipe. The 5-HP air motor delivers ample power to pump 180 GPM @ 15 ft. head.

Wenesco Inc Pump. This pump for molten salt features an immersion depth of 144 inches. It is made from 316 stainless steel. This pump includes a 3-in NPT discharge pipe. The 5-HP air motor delivers ample power to pump 180 GPM @ 15 ft head.
Wenesco Inc Pump. This pump for molten salt features an immersion depth of 144 inches. It is made from 316 stainless steel. This pump includes a 3-in NPT discharge pipe. The 5-HP air motor delivers ample power to pump 180 GPM @ 15 ft head.
H-Frame Pumps

(Below) For Zinc, Lead, & Other Soft Metals

H-frame pumps for Zinc and Lead are made to order.

  • STYLE HS has 54 inch maximum immersion.

  • STYLE HL has 81 inch maximum immersion

  • Electric or air motors up to 25 HP

  • Explosion-proof motors. (Class 1,Div 2) is optional

  • Cast iron volute and impeller

  • 304 Stainless steel shaft and frame

  • Heavy duty hooks mounted to frame to raise and lower the pump.

Weneso Inc Pump. H-Frame Pumps
Wenesco Inc. H-Frame Pump
H-Frame Pumps

(Below) Suitable for shorter immersion depths with a wide selection of motors.

Click HERE to head back to the Homepage and learn more about our full line of Industrial Heating Equipment