Wenesco High-Temperature Pumps

 

For any questions regarding our High-Temperature Pumps, please reach out to Enver Poljak, at Enver@wenesco.com.

Wenesco High-temperature Pumps are used for transferring molten salt, zinc, lead, and other non-viscous material at 700C.

These centrifugal pumps, with no seals, require only minimal maintenance. They are available with electric or air motors.

Wenesco Model HTP1  with 1-HP motor
Wenesco Pump. Wenesco Pump Total Head in feet vs capacity in US gallons per minute

TUBE FRAME PUMPS

  • Select 120 or 240V for electric motor

  • Select 304 stainless steel or cast iron construction

  • Starter with thermal protection

  • Discharge: 1.25 NPT

  • Complete air control for air motor

  • 316 SS construction optional at additional cost

  • Gussets for lowering pump during operation

  • VFD Speed control optional at additional cost

Wenesco Model HTP1 with air motor
Wenesco Pump Total Head in feet vs capacity in lb/min
Model HTP2 with 2-HP motor
Wenesco Pump Diagram
Molten Salt Pumps
Wenesco Molten Salt Pump custom made for mounting in our customer’s tank
Wenesco This temperature-controlled heated tank, combined with a high temperature pump  delivers molten salt, used as a coolant. to a Molten Salt Reactor.
The 316-stainless steel reservoir holds 7-1/2 gallons (120 lb. salt) and will operate up to 700C.  Temperature is controlled with an accurate digital thermostat, while pump speed and flow  are controlled with a Variable Frequency Drive.  Power: 13,800 Watts, 240V single or three-phase. Wenesco Molten Salt Pump

(Above) Molten Salt Pump custom made for mounting in our customer’s tank

Wenesco Molten Salt Loop Test System

(Above) This temperature-controlled heated tank, combined with a high temperature pump
delivers molten salt, used as a coolant. to a Molten Salt Reactor.

The 316-stainless steel reservoir holds 7-1/2 gallons (120 lb. salt) and will operate up to 700C.
Temperature is controlled with an accurate digital thermostat, while pump speed and flow
are controlled with a Variable Frequency Drive. 

 

Power: 13,800 Watts, 240V single or three-phase.

(To The Left) Molten Salt Loop Test System

(Below) This pump for molten salt features an immersion depth of 144 inches. It is made from 316 stainless steel. This pump includes a 3-in NPT discharge pipe. The 5-HP air motor delivers ample power to pump 180 GPM @ 15 ft. head.

Wenesco Inc Pump. This pump for molten salt features an immersion depth of 144 inches. It is made from 316 stainless steel. This pump includes a 3-in NPT discharge pipe. The 5-HP air motor delivers ample power to pump 180 GPM @ 15 ft head.
Wenesco Inc Pump. This pump for molten salt features an immersion depth of 144 inches. It is made from 316 stainless steel. This pump includes a 3-in NPT discharge pipe. The 5-HP air motor delivers ample power to pump 180 GPM @ 15 ft head.
H-Frame Pumps

(Below) For Zinc, Lead, & Other Soft Metals

H-frame pumps for Zinc and Lead are made to order.

  • STYLE HS has 54 inch maximum immersion.

  • STYLE HL has 81 inch maximum immersion

  • Electric or air motors up to 25 HP

  • Explosion-proof motors. (Class 1,Div 2) is optional

  • Cast iron volute and impeller

  • 304 Stainless steel shaft and frame

  • Heavy duty hooks mounted to frame to raise and lower the pump.

Weneso Inc Pump. H-Frame Pumps
Wenesco Inc. H-Frame Pump
H-Frame Pumps

(Below) Suitable for shorter immersion depths with a wide selection of motors.

Click HERE to head back to the Homepage and learn more about our full line of Industrial Heating Equipment

Microptik BV is our distributor serving Europe, the Middle East, Africa, and Asia. Visit their site: www.wenesco.eu

© 2018 Designed by Adam Victorn - Wenesco - Entire site copyright 1998-2020 by LDS Industries, LLC. All rights reserved.